vector.com|Contact
Search tips

apple banana
Find rows that contain at least one of the two words.

+apple +juice
Find rows that contain both words.

+apple macintosh
Find rows that contain the word 'apple', but rank rows higher if they also contain 'macintosh'.

+apple -macintosh
Find rows that contain the word 'apple' but not 'macintosh'.

+apple ~macintosh
Find rows that contain the word 'apple', but if the row also contains the word 'macintosh', rate it lower than if row does not. This is "softer" than a search for '+apple -macintosh', for which the presence of 'macintosh' causes the row not to be returned at all.

+apple +(>turnover >strudel)
Find rows that contain the words 'apple' and 'turnover', or 'apple' and 'strudel' (in any order), but rank 'apple turnover' higher than 'apple strudel'.

apple*
Find rows that contain words such as 'apple', 'apples', 'applesauce', or 'applet'.

"some words"
Find rows that contain the exact phrase 'some words' (for example, rows that contain 'some words of wisdom' but not "some noise words").

By continuing to use this site you agree to the use of cookies. For more information and to find out how to change this click here. Accept Cookies
Please enable cookies in your browser for this website.
Search:
Advanced search
VX Hardware Family
document
2019-02-25 Adjusting the VX1000 Ethernet Settings
IP Address of the VX1000 base module All VX1000 base modules are delivered with the IP-Address 192.168.0.2. Firewall Settings To be able to connect with a VX1000 base module via Ethernet, you should first turn off the firewall on your PC (if a firewall is active). Ask your administrator to...
2019-02-25 rating Views: 2317
document
2019-02-25 Update of the VX Module Firmware
VX Firmware update In the VXconfig software you can check and update the firmware version of the VX hardware and the VX POD. To have the latest firmware please go to the Vector website Download Center and download the latest VXtools version. To update the firmware please perform the following...
2019-02-25 rating Views: 1922
document
2018-12-12 Usage of VX113x with CANoe
Support Note: The following Support Note describes how to use a VX113x Hardware with CANoe. Please note that as the VX113x cannot contain any license bit for CANoe, another license carrier (Vector Keyman dongle, CANcaseXL, VNxxxx with CANoe license) shall be connected to the PC.
2018-12-12 rating Views: 1725
document
2019-02-25 VX113x interface(s) with CANape
Support Note: The following Support Note describes how to use CAN or FlexRay interfaces of a VX113x Hardware with CANape.
2019-02-25 rating Views: 1461
document
2019-02-25 Start the VX Console
The VX console In the VXconfig software you start a console called VXconsole. This console allows you to show some information about the status of the VX hardware and the VX POD. To start the VXconsole please perform the following steps. Starting the VX console Start the VXconfig software...
2019-02-25 rating Views: 1352
document
2019-02-25 VX1000 Base Modules: Standby Mode
VX1060 Base Modules labeled with ECO and all VX1132 Base Modules support a standby mode. These devices can enter a power-saving state which is indicated by a red-blinking PWR LED with all other LEDs off. For this, in VXconfig in the device Network Settings "Standby Mode" must be enabled. If so,...
2019-02-25 rating Views: 1184
document
2019-02-25 Enabling/Disabling Debug Mask
The Debug Mask In the VXconfig software you can enable/ disable a debug mask, which can generate additional debug information on the VX console. To enable/disable the debug mask please perform the following steps. Enable or disable the debug mask Start the VXconfig software (you should have an...
2019-02-25 rating Views: 1002
document
2019-02-25 Reducing the Latency on a Bypass Function
Priority threshold in VXconfig In VXconfig there is an option to define a value for a priority threshold. This value can be set between 0 (lowest priority) and 255 (highest priority). All measurement signals bound to an XCP event channel with a higher priority than the priority threshold...
2019-02-25 rating Views: 965
document
2019-02-25 Reading out and Saving Vxparameter Set
The VXparameter set In the VXconfig software you can save the VXparameter set in a file (xxx.ini). To save the VXparameter set please perform the following steps. Read the VXparameter set from a VX Hardware Start the VXconfig software and and choose your VX device (you should have an...
2019-02-25 rating Views: 770
document
2019-06-14 Timestamp Synchronization with Multiple VX1135 or Other VX1000 Interfaces
Question: How can I synchronize the timestamps of multiple VX1000 interfaces in one measurement? Which cable or connector shall I use? Answer: The synchronisation is done by interconnecting the interfaces with sync cables as described below. For CANape, additionally Hardware...
2019-06-14 rating Views: 70